MAG DRIVE CENTRIFUGAL PUMPS
248.588.1500     KNOLL
MAG DRIVE CENTRIFUGAL PUMPS
For Chemical Applications

These pumps are suitable for various applications in the chemical, plating and water treatment fields. Simplicity of design insures the minimum components for cost and ease of repair. The elimination of the shaft seal limits liquid leakage of aggressive fluids due to the lack of component wear.



Pumps cannot be operated in dry run condition. They are designed for clean liquids only. Dirty or contaminated fluids can reduce pump life. Pump should be mounted horizontal and below the liquid level to prevent dry running.


ComponentsMaterial
1ShaftAlumina
Ceramics 99.7%
2Thrust bearing
washer
PTFE +
30% Graphite
3BearingPTFE +
30% Graphite
4O-ringVITON/EPDM
5ImpellerPP/PVDF+CF
6Pump CasingPP/PVDF+CF
7Head thrust
bearing washer
Alumina
/Ceramics 99.7%
 

Pump housing and impeller material is either polypropylene (PP) or polyvinylidene (PVDF).

Fluid Temperature:
PP         -50°F to 149°F
PVDF    -50°F to 194°F

Viscosity up to 150 CPS

KNOLL     248.588.1500
MAG DRIVE CENTRIFUGAL PUMPS

For Chemical Applications
MAG DRIVE CENTRIFUGAL PUMPS


ITEM #MOTOR H.P.IMPELLER (MM)INLET NTP
MALE
OUTLET NTP
FEMALE
MAX HEAD IN
METERS
MAX FLOW IN
G.P.M.
UNIT PRICEQTY
DM06PP1/20.813/4"1"1035$675.00
DM10PP3/40.851"1-1/2"1055$755.00
DM12PP10.981"1-1/2"1470$790.00
DM14PP21.081-1/4"1-1/4"1590$1,915.00
DM15PP30.1231-1/4"1-1/4"20120$980.00
DM30PP50.1341-1/2"2"25180$1,530.00
PVDF
ITEM #MOTOR H.P.IMPELLER (MM)INLET NTP
MALE
OUTLET NTP
FEMALE
MAX HEAD IN
METERS
MAX FLOW IN
G.P.M.
UNIT PRICEQTY
DM06FC1/20.813/4"1"1035$790.00
DM10FC3/40.851"1-1/2"1055$1,040.00
DM12FC10.981"1-12"1470$1,160.00
DM14FC21.081-1/4"1-1/4"1590$2,520.00
DM15FC30.1231-1/4"1-1/4"20120$1,520.00
DM30FC50.1341-1/2"2"25180$2,160.00
Options available upon request. TEFC motors, inlet and outlet flanges, and viton o-rings.
CHECK VALVES
Designed for vertical installation at the bottom end of the suction pipe on both centrifugal and pneumatic pumps. These non-return valves prevent fluid from flowing out of the suction pipe. This allows the pump to remain primed at all times.

POLYPROPYLENE
ITEM #SIZE BSPP UNIT PRICEQTY
VALVFN000012APP1/2"$77.00
VALVFN000100APP1"$98.00
VALVFN000114APP1-1/4"$122.00
VALVFN000112APP1-1/2"$215.00
VALVFN000200APP2"$250.00
PVDF
ITEM #SIZE BSPP UNIT PRICEQTY
VALVFN000012AFV1/2"$105.00
VALVFN000100AFV1"$155.00
VALVFN000114AFV1-1/4"$350.00
VALVFN000112AFV1-1/2"$380.00
VALVFN000200AFV2"$590.00